The Basics of Plumbing Skills When Installing a Bathtub
The Basics of Plumbing Skills When Installing a Bathtub
Blog Article
Were you trying to locate answers concerning Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, however it does need solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is easily accessible, the task can move quickly; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub and also embeded in the new one. Ensure you have actually qualified yourself for the work and also fit trying it. Instead of employing a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Chances are you may need a specialist plumber to make tube connections.
This article will assist you set up a new bathtub in your bathroom if you have currently bought a brand-new bathtub as well as don't need to change the setup of your previous water system pipes.
Your devices and also product checklist should consist of the following:
Planning for the Setup
To start with, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the tub until the level reviews level.
To install taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
Turn on the water system and inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill the tub and likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has been made use of at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The former kind should be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very drawn to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the entry. I beg you take a moment to distribute this article if you enjoyed reading it. Thanks so much for your time spent reading it.
Estimate Report this page